Balcony Waterproofing
As opposed to toilet and kitchen waterproofing, balcony waterproofing has to be of much higher quality and durability due to its 24/7 exposure to the weather. Any leakage through balconies is troublesome because the balcony is exposed to weather under a roof slab. It withstands weather action (heat, storm water, cyclical wetting and drying processes).
This must be considered for right selection of waterproofing product, otherwise leakage will occur and it is difficult to get rid of the problem permanently.
NANOFIX RECOMMENDS FOLLOWING PRODUCTS FOR YOUR BALCONY
Nanofix 0102 :
Nanofix 0102 is acrylic co polymer based economical milky white waterproof coating compound with Nano particles for enhancing water proofing properties of concrete & masonry surfaces.
Nanofix FLEXEET :
Nanofix Flexeet is two components ready to use resin based Nano composite heavy duty waterproof coating.
Nanofix Plastoseal :
This is crack sealing compound. If any crak is observed on the mother slab, Plastoseal is applied to seal all the cracks. Joint between mother slab and parapet is also sealed by Plastoseal to prevent the seepage through joint, so that paint blistering and patches outside parapet do not appear.
NANOFIX Methodology for Balcony Waterproofing
Step-1:- Surface preparation
- Surface should be dry cleaned by removing loose scales, dirt, dust, grease, oil etc. by wire brush.
- Any visible cracks to be repaired with Nanofix Plastoseal.
- The joint between parapet brick work and R.C.C. slab & annular gaps of the pipes ( if any ) with Nanofix Plastoseal and to flash at both the end.
- The floor and the wall junctions should be cleaned thoroughly.
Step-2:- Application of Nanofix Protective waterproof coating
You are suggested to select any of the following two recommended solutions for most effective balcony waterproofing.
Nanofix 0102 :
- Surface should be dry cleaned by removing Loose Scales, Dirt, Dust, Grease, Oil etc. by Wire Brush
- Any visible cracks to be repaired with Nanofix Plastoseal
- Prepare waterproof coating by mixing Nanofix 0102 with water & cement in 1:2:2 ratio and apply the first coat by brush
- After drying of first coat for 6 to 8 hrs (depending upon weather condition) apply second coat in same recommended ratio by brush uniformly
- Sprinkle sand only in case of application on brick & concrete surface. Screed or plastering should be done after drying of 8 hrs.
Nanofix Flexeet :
- Surface should be Dry Cleaned by removing Loose Scales, Dirt, Dust, Grease, Oil etc. by Wire Brush
- Mix Part A with Part B homogeneously and then add Water slowly to make Brush Applicable Coating (Mixing Ratio – Part A : Part B: Water = 1:1:1)
- Apply First Coat by Brush
- After drying of First Coat for 6 to 8hrs (Depending upon Weather Condition) apply Second Coat by brush uniformly
- Sprinkle Sand only in case of application on Brick & Concrete Surface. Screed or plastering should be done after drying of 8hrs.
Nanofix Plastoseal :
- Surface must be free from Dust, Oil, Grease and Loose Particles etc. Fine hair line cracks must be widened up to 1 – 2 mm minimum by using chisel or scrapper and then filled.
- Apply the paste firmly into the crack with a Spatula or Putty Knifes and level with the Surface. Allow it to set for 24 hours. But over coating is possible after 6 – 8 hrs depending upon the weather condition.
Step-3:- Lying of plaster Screed
- The plaster screed should be laid after drying of 8 hrs.
For detail specification & assistance as per your need, please contact our technical division.
Material Handling & Safety Information :
- Nanofix product should be stored in closed container in a cool, dry place away from direct sunlight
- Maintain safety during execution of the waterproofing jobs and due care to be taken while handling Nanofix & other construction materials.
- Nanofix materials are nontoxic. Hands and tools should be washed with normal water.
- NANOFIX recommends the enforcement of stringent health and safety measures at all job sites.
